Questions & Answers

EVO-ONE wont start with oem remote with factory alarm.

0 votes

Service no 002B05 027677

 

Hello.  I`m trying to take a work EVO-ONE for subaru outback 2011, automatic transmision, with  factory alarm. so loop is cuted. i used GUIDE # 46701 for harness conection. turning on ignition yelow light goes on. when i pushing lock button 3 times nothing going at all (blue light- no, red light - no). is there problem in incorrect flashing?

 

Service No: 002B05 027677
Preload date: 47-2015
Hardware version: 5
Firmware version: 1.17
Recommended version: 1.16
 
 

 

posté Jan 30, 2016 dans la catégorie Subaru par shemis.pro Alex (200 points)
modifié Fev 2, 2016 par shemis.pro Alex

2 Réponses

+2 votes
Turn on options A1 to A11.
répondu Fev 1, 2016 par shemis.pro Alex (85,210 points)
Hello. I will try it tomorrow evening. Thanks for fast answ.
I was turned on from A1 to A11, but it still no starts.

My suggestion is doing a master rest of the remote starter, as well as the bypass and re program the bypass module start to finish including DCryptor.

Your options are over lapping each other and you've also enabled options you shouldn't have. Doing a master reset will put everything back the way it should be.

Then simply enable options C1 bypass side and 38.2 remote starter side nothing else.

Here is how to reset the remote starter:

1- turn ignition on

2- press and hold valet switch until parking lights turn on (or red led under the yellow loop begins to flash)

3- press and release the valet switch 23 times

4-press and release the brake pedal once

5- press and hold valet switch for 5 seconds. Pakring lights will flash to confirm.

6- turn the ignition off (park lights will flash 4 times to confirm exiting programming).

Be sure to reset the remote start side first as you will loose your brake pedal input if you do the bypass first and don't reprogram it.

Here is how to reset the bypass:

  1. Hold down programming button while plugging in datalink connector.
  2. Let go of button when LED is RED.
  3. Push and hold button again until all three LEDs start to alternate.
  4. Disconnect unit, she is now reset.

 

when blue light must turn on? pressing oem remote to close or open doorlock? there are no blue flashes at all. so what i must to do?

"""Here is how to reset the bypass:

  1. Hold down programming button while plugging in datalink connector.
  2. Let go of button when LED is RED.
  3. Push and hold button again until all three LEDs start to alternate.
  4. Disconnect unit, she is now reset.""""

 

how long i must hold button?

ok. i think i was reseted unit. now i am conicting like bypass to flash link manager, bud dcryptor shows me green key, so i was start over, go back to car, folow KEY BYPASS PROGRAMMING PROCEDURE 2/2 from 46701, go back to F.L.Managaer to process dcryptor. now i must to toggle program to set options on remote starter?

 

"Then simply enable options C1 bypass side and 38.2 remote starter side nothing else."

nothing new... sad

so you reset both sides to the module and also re program and re DCrypted the module and still nothing?
yes- still not working
turn off function 6 in the remote starter. Also dis able function 24 in the remote starter as well.

I think i will leave this till saturday and will check all wiring. then i will reset again so i will let You know saturday. realy thanks for trying to help me yes

it still wont start. i think i lost my money with Fortin evo-one :(
0 votes
Hi again. so i was checked all wiring- all set. i was make reset of both sides (remote starter & bypass) then reflashed, but it still not works, so what i can more to do?
répondu Fev 6, 2016 par shemis.pro Alex (200 points)
no functionig module. i think i will trash it. lost my money :(
This car has been done many times, does the blue LED on the module flash every time you press the lock button ?
no.  blue light does not goes on then pushing lock button.
http://fortin.ca/en/vehicles/subaru/outback/2011/

Your vehicle is not listed as 3x lock compatible. You will need a seperate RF kit to start and stop the vehicle.
can i connect codealarm CA4054?
what modules is compactible with fortin ? what i must to buy now?

All comnpatible RF kits are listed here:https://fortin.ca/en/technology/rf_kits.html

 

Please click on the EVO-ONE pdfs please to get the proper guide.

Yes that will work with the Evo-One, please follow this guide for programming: https://fortin.ca/download/29221/EVO-ONE%20RF-KIT%20CrimeStopper%20REVO.pdf

 

Thank you.

THANK YOU FOR HELPING ME TO RESOLVE MY PROBLEM !!!!

I will buy this revo set and will try it to install.  yes

...