Questions & Answers

Tundra Shut down after a second after remote start

0 votes
Sometimes after remote start the tundra 2015, the vehicle shutdown . what if wire the yellow wire from evo all to Ign1 and Ign2 ? I'm thinking that with ign 1 only maybe is not enough . I've select monitor oem and D2D options, any more option to enable ? Thanx
asked Jul 30, 2015 in Toyota by Ara Her (770 points)

1 Answer

0 votes
Depending on the remote starter installed, you will have to check the parking light diagnostics of your remote starter if it is capable to find out why the remote starter is shutting down,

 

The Yellow wire (A1) from the Evo-All is only a "sense" wire, it does not output TO the vehicle.

 

Please provide us with the service number of the Evo-All and the year of the vehicle.

 

Thank you.
answered Jul 30, 2015 by J M (64,060 points)
Thank you for your answer. SN: 001A06 129407, the after market is Avital 4113. and model 2015 Everything is fine but as Ive mentioned before, vehicle sometime start notmal and sometimes starts for 1 second and after that shutdow.

Thanx
commented Jul 30, 2015 by Ara Her (770 points)

Are you getting any parking light flashes after it fails to start? Also which data port are you connected to on your Avital unit?

 

I would start there to diagnose the issue you are having.

ALSO, ign 1 and 2 should already be being powered up by your remote starter.

commented Jul 30, 2015 by J M (64,060 points)
edited Jul 30, 2015 by J M
No parking light flashes, its start for 1 second like no enough power. Car baterry is fine.

 Ign1 and Ign 2 are connected to remote start. and using D2D data port.
commented Jul 30, 2015 by Ara Her (770 points)
disable unlock before start in the remote starter settings. If you need this feature, enable it in the EVO-ALL instead. Also, DEI has mentionned having issues lately with their D2D protocol, you may need to do wire-to-wire and not datalink.

One more thing about toyota, if you have accessory connected, disconnect it.
commented Jul 30, 2015 by Robert T (300,020 points)
Thanx Robert. No accessory connected on Tundra. There is no such option on the Avital. What if I enable, unlock beofre and lock after remote start on Evo All options? I will try that. Ahm, one more thing, normally the vehicle if not success to start attemp to start totally 3 times. but in this case when shut off after one second, not attemp to start again. What if I try to enable this otion on Evo all? second attemp
commented Jul 30, 2015 by Ara Her (770 points)
The second attempt option on the evo-all is only for stand alone remote starter setups. In this setup, the evo-all is only used as transponder bypass and can-bus convenience features for the Avital.

Menu 1 option 7 in the Avital seems to be setup for disarm on remote start. Just looked at their guide and it doesn't seem that you can turn it off.
commented Jul 30, 2015 by Robert T (300,020 points)
 Ive just read this on tundra guide for evo all. I will try tomorrow:
 
Some vehicles must be UNLOCKED to disarm the OEM alarm
before remote start. Enable option D2 using the FlashLink
Manager. When this option is enabled the module will
automatically UNLOCK before remote start and LOCK after
the vehicle has remote started.
commented Jul 30, 2015 by Ara Her (770 points)
edited Jul 30, 2015 by Ara Her
 Ive just read this on tundra guide for evo all. I will try tomorrow:
 
Some vehicles must be UNLOCKED to disarm the OEM alarm
before remote start. Enable option D2 using the FlashLink
Manager. When this option is enabled the module will
automatically UNLOCK before remote start and LOCK after
the vehicle has remote started.
commented Jul 30, 2015 by Ara Her (770 points)
works fine now after enable unlock and lock option. thanx. Coudl you please show which wire send GND when lock is pressed on the remote?
commented Jul 31, 2015 by Ara Her (770 points)

We control doorlocks through CAN-BUS on this vehicle. so there are no analog doorlock outputs coming from the Evo-All.  Are you having issues with the doorlocks?

 

If you need analog doorlock control, those wires can be found at the driver's kickpanel in a blue connector, White and Red for lock and unlock. And Light Blue and Pink for Arm and Disarm. You will need to connect those to your remote starter. BUT we recommend that all doorlock controls be handled by the Evo-All

commented Jul 31, 2015 by J M (64,060 points)

Related questions

...